Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
2.1. Petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.2. Mechanical part of petrol Z10XE, Z10XEP, Z12XE, Z12XEP DOHC-I engines
2.3. Cooling system
2.4. Lubrication system
2.5. System of injection
2.6. Petrol engines – the general procedures of check
2.7. Mechanical part of the engine
2.8. Test and repair operations of components of a mechanical part of the engine
2.9. Cooling system
2.10. System of injection of fuel of petrol engines
2.10.1. Removal and installation of fuel nozzles
2.10.2. Replacement of a fuel-supply line of high pressure (The pump of high pressure – the pressure chamber)
2.10.3. Module of the fuel pump
2.10.4. Replacement of the module of a dosage
2.10.5. Replacement of the regulator of pressure of fuel
2.10.6. Replacement of damping fuel return case
2.10.7. Replacement of the fuel level sensor
2.10.8. Fuel tank
2.10.9. Replacement of a tube of a jellied mouth of the fuel tank (petrol engines)
2.10.10. System of catching of vapors of fuel
2.10.11. Replacement of a forward ventilating tube
2.10.12. Removal and installation of container with absorbent carbon
2.10.13. Removal and installation of the sensor of a mass consumption of air
2.10.14. System of release (Z 14 XEP, Z 14 XEL, Z 16 XEP)
2.10.15. System of release (Z18 XE)
2.11. Lubrication system
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 





0653563c

2-10-5-zamena-regulyatora-davleniya-topliva.html

2.10.5. Replacement of the regulator of pressure of fuel

Removal
Remove an inlet collector, having turned off a fastening bolt.
Remove a ventilating hose of the engine from a cover of a head of the block of cylinders.
Disconnect an inlet pipe from an air inlet hose.
Disconnect an inlet pipe from a turbocharger.

NOTE
Close an inlet pipe of a turbocharger.

Remove an inlet pipe.
Dump fuel pressure via the test union using the device for check of tightness of KM-J-34730-91.
Collect the following fuel in a suitable container.
Disconnect the vacuum highway (1) from the regulator of pressure of fuel (2). Remove a collar of fastening (5) from the regulator of pressure of fuel and a fuel stage.
Mark adjusting situation and accurately remove the fuel pressure regulator from a fuel stage.

NOTE
In this point absolute purity is extremely important.

Replace sealing rings.

Installation
Before installation cover sealing rings with a thin layer of silicone lubricant (white).
Note adjusting position of the regulator of pressure of fuel. Install the fuel pressure regulator in a fuel stage.

NOTE
In this point absolute purity is extremely important.

Establish a collar of fastening of the regulator of pressure of fuel and attach a fuel stage, tighten the moment 5 N · m.
Connect a vacuum hose to the fuel pressure regulator.
Remove a cap of an inlet pipe of a turbocharger.
Attach a ventilating hose of the engine to a cover of a head of the block of cylinders and fix by a collar.
Attach an inlet pipe to a turbocharger.
Attach an inlet pipe to an air inlet hose.
Wrap a bolt of fastening of a collar.


"on the page back
2.10.4. Replacement of the module of a dosage
on the following page"
2.10.6. Replacement of damping fuel return case