Repair of Opel Corsa C, from 2000 to 2005 release.
1. Operation and maintenance of the car
2. Engine
3. Transmission
4. Running gear
4.1. General information
4.2. Wheels and tires
4.3. Running gear
4.4. Forward suspension bracket
4.4.1. Removal and installation of the stabilizer of the forward bridge
4.4.2. Removal and installation of a rotary fist
4.4.3. Removal and installation of the lever of an independent suspension bracket
4.4.4. Replacement of all rubber bearings of the stabilizer
4.4.5. Removal and installation of a depreciation rack with the shock-absorber
4.4.6. Dismantling and assembly of a depreciation rack
4.5. Back suspension bracket
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment
 





0653563c

4-4-2-snyatie-i-ustanovka-povorotnogo-kulaka.html

4.4.2. Removal and installation of a rotary fist

Removal
Remove a forward wheel.
Note situation concerning a wheel nave.
Removal of a half shaft from a wheel nave.
Take off a dust cap.

NOTE
The dust cap is not removed without damages.

Remove the lock forelock 2 from a nut of a half shaft 3.
Install KM-6610 adaptation on a wheel nave by two screws of a wheel 4.
Remove a nut of a half shaft 3, hold KM-6610 5 together with the extender KM-956-16.
Remove KM-6610 adaptation.
Remove a brake disk.
Remove a head of cross steering draft.
Install CH-47658 2 adaptation in the correct situation.

NOTE
Center by means of a nozzle of a face key.

Use the suitable plug 4. The plug 4 has to adjoin densely to the lever of cross steering draft 3. Tighten CH-47658 2 adaptation for a hexagon 1.
Unscrew a nut 5.
Remove CH-47658 2, weaken with the help of a hexagon 1.
Remove the holder of the wheel sensor 1 with the ABS wheel sensor from a rotary fist.
Unscrew the screw.
Remove a head of cross steering draft 2.
Remove KM-507-C 3 adaptation from a rotary fist.
Remove a rotary fist from the directing hinge.
Unscrew a nut with the screw 4.
Remove a basic pipe of a depreciation rack from a rotary fist.

NOTE
When replacing a rotary fist reinstall the closing plate of a brake disk and use the new bearing of a wheel.

Unscrew 2 nuts with the screw 5.

Installation
Establish a rotary fist 1.
Implant a rotary fist into the directing hinge of the lever of an independent suspension bracket 2.
Remove a half shaft 3 in a wheel nave.
Establish a basic pipe of a depreciation rack on a rotary fist, tighten 2 new screws of a nut of 4 80 N · m + 60 ° +15 °.
Tighten the screw 7 of the directing hinge of 60 N · m.
Use a new nut.
Establish a head of cross steering draft 6 on a rotary fist.
Install CH-47658 adaptation in the correct situation.

NOTE
Center by means of a nozzle of a face key. Use the suitable plug. The plug has to adjoin to the lever of cross steering draft densely. Tighten CH-47658 adaptation for a hexagon.

Tighten a nut of 35 N · m.
Remove CH-47658 adaptation, weaken its fastening with the help of a hexagon.
Establish the holder of the wheel sensor 5 with the ABS wheel sensor on a rotary fist 8 N · to m.
Establish a brake disk.
Fix a half shaft on a wheel nave.
Establish KM-6610 1 with 2 screws of a wheel on a wheel nave.
Tighten a new koronchaty nut 1 and a washer 2 on a half shaft of 120 N · m.
Hold KM-6610 4 adaptation together with the extender KM-956-1 6.
Weaken a koronchaty nut 1 still koronchaty nut 1 will not turn by hand.
Tighten a koronchaty nut of 1 20 N · m + 90 °.
Install the new lock forelock.

NOTE
If it is necessary, turn a koronchaty nut 1 back until the opening under the forelock does not rise coaxially with the following cut of a koronchaty nut.

Remove KM-66104 adaptation.
Establish a new dust cap 5 on a wheel nave.
Establish a forward wheel – the moment of an inhaling of 110 N · to m.

"on the page back
4.4.1. Removal and installation of the stabilizer of the forward bridge
on the following page"
4.4.3. Removal and installation of the lever of an independent suspension bracket